CONMMCX012 Drawing Datasheet by Linx Technologies Inc.

Pin Insulano Crimp R Lack w lnsula Cover Heat Shrink PTFE N/A Brass Gold BE cu Gold PTFE N/A Brass Gold Polyoleﬁn Black v v ’o’o‘ Q o o’.‘ 0 Q C v 0:} o o ’o’o’o Q C 0.91 v 9 Q ’0 0:0 ‘¢ Q Q Q Q Q Q Q Q Q Q o?.?.% Q ’o’o’o’o’o‘ A Ad WARNlNG: MATERIAL FlNlSH AWlNG CONTAlNS PROPR ' ' ° ' ' OPERTV or UNX TECHNO No DlSCLOSUREOR REP lTrED, lN WHOLE OR lN TITLE: PERMlSSION OF LleT DESIGNATED AGENTS YULERAMES PROAECTlON oznlosﬂlrzoolsonlu xlozal zoulsaolsnoulaaoo . malow Izulaaolsusllzool Mosul , SIZE DWG. NO. 3 7S[1200]11w[315 m“ m ANGLES :1 DRAWN: DT: A 159 ORT LANE MERLIN, OR 97532 REV

NOTES: (UNLESS OTHERWISE SPECIFIED)

1. ALL DIMENSIONS ARE IN INCHES [mm].

2. DIMENSIONS APPLY AFTER FINISHING.

3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.

4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.

SHEET 1 OF 1

LDCFDLT_A

SCALE: 2:1

TITLE:

SIZE

DWG. NO.

REV

DO NOT SCALE DRAWING

ANGLES:

TOLERANCES:

.020 [0.50]-.200 [5.00]=

.008 [0.20]

.200 [5.00]-1.200 [30.00]=

.016 [0.40]

1.20 [30.0]-4.75 [120.0]=

.024 [0.60]

4.75 [120.0]-12.40 [315.0]=

.040 [1.0]

DRAWN:

ENGR:

DT:

MATERIAL:

FINISH:

PROJECTION:

THIS DRAWING CONTAINS PROPRIETARY INFORMATION

THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE

TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS

DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE

EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS

DESIGNATED AGENTS.

159 ORT LANE

MERLIN, OR 97532

1/13/10

REVISIONS

REV

DESCRIPTION

DATE

APPV

BNew frame; revised heat shrink dimensions 1/13/10 CJ

CONMMCX012 ASSEMBLY INSTRUCTIONS

1. Strip the cable to the recommended dimensions.

2. Slip heat shrink and crimp ring onto stripped cable.

2. Slide the cable into the body until the center conductor is centered in the fork.

3. Push the braided shield over the barrel.

4. Solder the center conductor into the center of the fork.

5. Slide the crimp ring over the shield and crimp with a 0.128” hex crimp tool

(or one labeled for use with RG-174 cable).

6. Trim off any excess shield wire sticking out from the ring.

7. Slip the heat shrink over the crimp ring until it is against the body and shrink.

8. Insert insulator into body.

9. Push the cover into the opening.

Description Material Finish

Body

Insulation

Gold

N/A

Gold

PTFE

Crimp Ring GoldBrass

Lock Washer GoldBE CU

Insulator

Cover

Heat Shrink

N/A

Gold

Black

PTFE

Brass

Polyoleﬁn

Brass

MMCX MALE RIGHT ANGLE

CABLE END CRIMP FOR RG174 CABLE

CONMMCX012

0.217

(5.50)

0.059

(1.50)

RECOMMENDED CABLE STRIPPING DIMENSIONS

0.028

(0.70)

RG-174 Cable

0.197

(5.00)

0.354

(9.00)

Ø0.093

(2.35)

0.104

(2.65)

0.138

(3.50)

0.270

(6.85)

Ø0.102

(2.60)

INSULATOR

BARREL

BRAIDED SHIELD

COVER

SIDE VIEW

Ø0.154

(3.90)

0.276

(7.00)

CRIMP RING

Ø0.197

(5.00)

0.787

(20.00)

HEAT SHRINK

CAdded new title block; Revised instructions 12-JUL-12 BPM

Products related to this Datasheet

CONN MMCX PLUG R/A 50 OHM SOLDER

CONMMCX012